{"title":"Oracle Audio Tonearms","description":"\u003cp\u003eOracle Audio designs each tonearm to complement the suspended sub-chassis and vibration control systems built into their turntables. Precision bearings, carefully selected materials, and tight manufacturing tolerances ensure accurate tracking across the full frequency range, letting the cartridge extract detail from the groove without coloration or resonance from the arm itself. Every tonearm is hand-assembled and tested at Oracle's facility in Sherbrooke, Quebec, with the same meticulous attention to mechanical precision that defines their turntable lineup. Effective mass, bearing friction, and resonance characteristics are optimized for each model's target platform, ensuring the arm and turntable perform as an integrated system rather than separate components.\u003c\/p\u003e\u003cp\u003eThe \u003ca href=\"\/products\/oracle-audio-origine-tonearm\"\u003eOrigin Tonearm\u003c\/a\u003e pairs with the \u003ca href=\"\/products\/oracle-audio-origine-mk2-turntable\"\u003eOrigin Mk2\u003c\/a\u003e turntable, while the \u003ca href=\"\/products\/oracle-audio-paris-tonearm\"\u003eParis Tonearm\u003c\/a\u003e is designed for the \u003ca href=\"\/products\/oracle-audio-paris-mkv-turntable\"\u003eParis MkV\u003c\/a\u003e. The \u003ca href=\"\/products\/oracle-audio-reference-tonearm\"\u003eReference Tonearm\u003c\/a\u003e is Oracle's flagship arm, engineered for the \u003ca href=\"\/products\/oracle-audio-delphi-mk-vii-classic-turntable\"\u003eDelphi Mk VII\u003c\/a\u003e platform where it takes full advantage of the MVSS vibration control and suspended sub-chassis. Custom \u003ca href=\"\/products\/oracle-audio-armboard\"\u003earmboards\u003c\/a\u003e are available for third-party tonearm compatibility across the Oracle range.\u003c\/p\u003e","products":[{"product_id":"oracle-audio-paris-tonearm","title":"Oracle Audio Paris Tonearm","description":"\u003cp\u003eThe Oracle Audio Paris Tonearm is a 9-inch gimbal-bearing arm built around a single-piece conical carbon fiber tube, four ABEC7 ball races in an inverted bearing assembly, and Oracle's proprietary Micro Vibration Stabiliser silicone damping system. With an effective mass of 8.5g and supplied counterweights covering cartridges from 3g to 15g, the Paris handles everything from high-compliance moving magnets to low-compliance moving coils. It was designed for the Oracle Paris turntable but fits other Oracle platforms as well.\u003c\/p\u003e\n\n\u003cp\u003eThe Paris is the middle of Oracle's three-arm lineup, and it's where Oracle's engineering starts to separate from the pack. The conical carbon fiber tube eliminates standing wave reflections that straight tubes create, and the Micro Vibration Stabiliser adds fluid damping on top of the carbon fiber's natural resonance control. That's two layers of vibration management before the signal reaches the wiring. At $1,255, the Paris competes with arms from Rega, Pro-Ject, and Jelco, but the combination of ABEC7 bearings, conical geometry, and silicone damping is unusual at this price. We recommend it to Paris turntable owners looking for the arm that was designed for their deck, and to Delphi owners who want a significant upgrade from the Origine without stepping up to the $6,000 Reference.\u003c\/p\u003e\n\n\u003ch5\u003eKey Features of the Oracle Paris Tonearm\u003c\/h5\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle-Piece Conical Carbon Fiber Arm Tube:\u003c\/strong\u003e Tapered design eliminates standing wave reflections and provides high rigidity with low effective mass\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInverted Gimbal Bearing:\u003c\/strong\u003e Four hardened ABEC7 ball races for precise, low-friction movement in both planes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMicro Vibration Stabiliser:\u003c\/strong\u003e Oracle's proprietary silicone fluid damping with a paddle-and-trough mechanism that absorbs tonearm resonances\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8.5g Effective Mass:\u003c\/strong\u003e Low enough for medium and high-compliance cartridges while stable with lower-compliance designs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMultiple Counterweight Options:\u003c\/strong\u003e Supplied weight covers 6-10g cartridges, with optional weights for 3-6g, 5-8g, and 10-15g ranges\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAzimuth Adjustment:\u003c\/strong\u003e Single-screw fixing allows arm tube rotation for precise alignment\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-Grade Copper Internal Wiring:\u003c\/strong\u003e Low-resistance signal path from headshell to output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable VTA:\u003c\/strong\u003e Solid arm base permits accurate height adjustment for vertical tracking angle\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch5\u003eConical Carbon Fiber Arm Tube\u003c\/h5\u003e\n\u003cp\u003eThe Paris uses a single-piece conical carbon fiber arm tube that tapers from a wider diameter at the bearing housing to a narrower diameter at the headshell. This geometry prevents standing wave reflections within the tube. In a straight, uniform tube, vibrations bounce between the ends, creating resonances that color the signal. The conical shape breaks up these reflections by continuously changing the cross-section along its length. Carbon fiber contributes high stiffness relative to its weight, so the tube resists flexing under groove modulation forces without adding unnecessary mass. The result is an effective mass of 8.5g, low enough for medium and high-compliance cartridges while remaining controlled with stiffer designs.\u003c\/p\u003e\n\n\u003ch5\u003eInverted Bearing Assembly\u003c\/h5\u003e\n\u003cp\u003eThe bearing system uses an inverted design with four hardened ball races manufactured to ABEC7 specification, a precision grade that defines tight tolerances on ball roundness, surface finish, and dimensional consistency. This translates to extremely low friction and virtually zero play in the assembly. The inverted orientation places the bearing's center of gravity below the pivot point, contributing to stability during tracking. The gimbal configuration constrains the arm to move freely in two planes (horizontal for tracking across the record, vertical for following warps) while preventing unwanted rotation. This is fundamentally different from unipivot designs, trading the unipivot's freedom of movement for directional stability.\u003c\/p\u003e\n\n\u003ch5\u003eMicro Vibration Stabiliser Damping System\u003c\/h5\u003e\n\u003cp\u003eOracle's proprietary Micro Vibration Stabiliser is a paddle-and-trough mechanism mounted to the underside of the arm. A paddle attached to the arm tube dips into a trough filled with silicone fluid. As the cartridge traverses from outer groove to inner, the paddle moves through the fluid, converting mechanical vibration into heat. This viscous damping works across a broad frequency range, absorbing micro-vibrations that travel up through the arm tube from the stylus-groove interface. Unlike purely mechanical damping (which tends to be frequency-specific), fluid damping provides consistent energy absorption regardless of vibration frequency. The system works alongside the carbon fiber tube's natural damping, addressing resonances at two points in the chain.\u003c\/p\u003e\n\n\u003ch5\u003eCartridge Matching and Counterweight System\u003c\/h5\u003e\n\u003cp\u003eThe Paris ships with a counterweight for cartridges in the 6-10g range, covering the majority of popular moving magnet and moving coil designs. Optional counterweights are available for 3-6g, 5-8g, and 10-15g cartridge weights, ensuring proper balance with virtually any cartridge on the market. The 18mm overhang and 212mm mounting distance establish the geometric relationship to the record surface. Azimuth adjustment uses a single-screw fixing that allows the arm tube to rotate for perpendicular stylus alignment. VTA is adjustable through the solid arm base for matching the cartridge manufacturer's recommended stylus rake angle.\u003c\/p\u003e\n\n\u003ch5\u003eOutput and Wiring Options\u003c\/h5\u003e\n\u003cp\u003eInternal wiring uses high-grade copper conductors from headshell pins to the output connection. The Paris is available with three output configurations: a 5-pole standard socket for use with a separate phono cable, flying leads for direct connection, or a terminal with RCA sockets and an earth screw. The headshell uses a standard 12.7mm (1\/2 inch) mounting, compatible with the vast majority of phono cartridges.\u003c\/p\u003e\n\n\u003ch5\u003eExplore the Oracle Audio Tonearm and Turntable Range\u003c\/h5\u003e\n\u003cp\u003eThe Paris Tonearm sits in the middle of Oracle's lineup. For those seeking the highest level of performance, the \u003ca href=\"\/products\/oracle-audio-reference-tonearm\"\u003eOracle Reference Tonearm\u003c\/a\u003e pushes bearing precision and damping further. Coming from a more entry-level arm, the \u003ca href=\"\/products\/oracle-audio-origine-tonearm\"\u003eOracle Origine Tonearm\u003c\/a\u003e offers Oracle's unipivot design at a lower price point.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-origine-mk2-turntable\"\u003eOracle Audio Origine Mk2 Turntable\u003c\/a\u003e\u003c\/strong\u003e - Oracle's entry-level turntable with included Origine tonearm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-origine-tonearm\"\u003eOracle Audio Origine Tonearm\u003c\/a\u003e\u003c\/strong\u003e - Unipivot tonearm in Paris and Delphi mount configurations\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-reference-tonearm\"\u003eOracle Audio Reference Tonearm\u003c\/a\u003e\u003c\/strong\u003e - Oracle's flagship tonearm for maximum tracking precision\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-delphi-mk-vii-classic-turntable\"\u003eOracle Audio Delphi Mk VII Classic\u003c\/a\u003e\u003c\/strong\u003e - Oracle's flagship turntable with full suspension\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-delphi-mkvii-reference-turntable\"\u003eOracle Audio Delphi Mk VII Reference\u003c\/a\u003e\u003c\/strong\u003e - Reference-grade Delphi with upgraded power supply\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch5\u003eThe Listening Room Difference\u003c\/h5\u003e\n\u003cp\u003eWe're a third-generation family business with a brick-and-mortar showroom in Chestertown, Maryland, and a reputation built on trust, not hype. Whether you're visiting in person or ordering online, we bring decades of experience, personalized service, and honest guidance to every interaction. We don't just ship boxes. We help build systems, answer your questions like real humans, and make sure every detail of your setup is right, from the cables to the final connection. Our passion is helping you get the most out of your gear, with support that lasts well beyond the sale.\u003c\/p\u003e\n\n\u003ch5\u003eOracle Paris Tonearm Specifications\u003c\/h5\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTonearm Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eGimbal (inverted bearing design)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArm Tube\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eSingle-piece conical carbon fiber\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEffective Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e230mm (9\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEffective Mass\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e8.5g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOverhang\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e18mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMounting Distance\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e212mm (platter to tonearm base)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBearings\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFour hardened ABEC7 ball races\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDamping\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMicro Vibration Stabiliser (silicone fluid paddle-and-trough)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eInternal Wiring\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHigh-grade copper\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eHeadshell Mount\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e12.7mm (1\/2\") standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSupplied Counterweight Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e6-10g cartridge weight\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOptional Counterweights\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3-6g, 5-8g, 10-15g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWeight (without counterweight)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e250g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Options\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5-pole socket, flying leads, or RCA terminal with earth screw\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCompatible Turntables\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eOracle Paris (primary), other Oracle models\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCountry of Origin\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHandcrafted in Sherbrooke, Quebec, Canada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Oracle Audio","offers":[{"title":"Default Title","offer_id":42547109363808,"sku":"ORACLEPARIS","price":1255.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0555\/5073\/8528\/files\/paris-tonearm.jpg?v=1770431363"},{"product_id":"oracle-audio-origine-tonearm","title":"Oracle Audio Origine Tonearm","description":"\u003cp\u003eThe Oracle Audio Origine Tonearm is a high-precision unipivot design with a carbon fiber arm tube, Cardas internal wiring, and Oracle's signature adjustable-mass system. Available in Paris Mount and Delphi Mount configurations, this tonearm brings Oracle's engineering directly to their Paris and Delphi turntable platforms. The unipivot bearing geometry places the pivot contact point on the same plane as the stylus contact and the tracking force counterweight, a layout that maximizes stability during playback.\u003c\/p\u003e\n\n\u003cp\u003eThe Origine sits at the entry point of Oracle's tonearm lineup, but calling it \"entry-level\" undersells what it does. The unipivot bearing geometry, adjustable effective mass, and Cardas wiring put it well ahead of most arms bundled with turntables in the $2,000-$4,000 range. We recommend the Origine as a standalone upgrade for Paris and Delphi owners who want better tracking and signal retrieval without jumping to the Paris Tonearm's price point. If you're running the stock arm on a Paris MkV or want a second arm option for your Delphi, this is the most cost-effective step up in Oracle's range.\u003c\/p\u003e\n\n\u003ch5\u003eKey Features of the Oracle Origine Tonearm\u003c\/h5\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCarbon Fiber Arm Tube:\u003c\/strong\u003e Lightweight, rigid tube that controls resonance while keeping effective mass low enough for a broad range of cartridge compliances\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnipivot Bearing Design:\u003c\/strong\u003e Single-point pivot with the contact point aligned on the same plane as the stylus and counterweight for inherent stability\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable Effective Mass:\u003c\/strong\u003e The movable \"olive\" weight on the arm tube lets you tune effective mass to match your specific cartridge, from high-compliance moving magnets to low-compliance moving coils\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardas Internal Wiring:\u003c\/strong\u003e Signal path from headshell to RCA junction box uses Cardas conductors for low-loss signal transmission\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRCA Junction Box:\u003c\/strong\u003e Clean, secure output connection included with the tonearm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo Mounting Configurations:\u003c\/strong\u003e Paris Mount for Paris turntables and Delphi Mount for the Delphi series, ensuring correct geometry on each platform\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHandcrafted in Canada:\u003c\/strong\u003e Built to order at Oracle's Sherbrooke, Quebec facility\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch5\u003eUnipivot Bearing Geometry\u003c\/h5\u003e\n\u003cp\u003eThe Origine Tonearm's unipivot bearing was designed with a specific geometric principle in mind. The pivot contact point sits on the same plane as the record's contact point with the stylus and the tracking force counterweight. This three-point alignment creates inherent stability during playback, allowing the arm to track the groove with minimal lateral wobble while still maintaining the freedom of movement that makes unipivot designs effective at following warped records and eccentric grooves. Unlike gimbal-bearing tonearms that constrain movement to two fixed axes, the unipivot allows the arm to respond naturally to the record surface, adapting in real time to changes in groove modulation and surface irregularities.\u003c\/p\u003e\n\n\u003ch5\u003eArm Tube and Resonance Control\u003c\/h5\u003e\n\u003cp\u003eThe carbon fiber arm tube provides an optimal balance of rigidity and low mass. Carbon fiber's natural damping characteristics help suppress resonances that would otherwise color the signal retrieved by the cartridge. The tube's stiffness ensures that energy from the stylus-groove interaction is transmitted efficiently to the bearing rather than being stored and re-released as distortion. The \"olive,\" Oracle's movable arm tube weight, serves a dual purpose. It allows you to adjust the tonearm's effective mass to match your cartridge's compliance, and it also functions as a tuned damper, absorbing residual vibrations along the arm tube. This adjustability means the Origine can accommodate cartridges across a wide compliance range without requiring a different tonearm for each type.\u003c\/p\u003e\n\n\u003ch5\u003eCartridge Compatibility and Setup\u003c\/h5\u003e\n\u003cp\u003eThe adjustable effective mass system makes the Origine Tonearm compatible with a broad range of phono cartridges. By repositioning the olive along the arm tube, you can increase or decrease the effective mass to achieve the correct resonance frequency with your chosen cartridge. The goal is to place the arm-cartridge resonance in the 8-12 Hz range, well below audible frequencies but above the frequencies generated by record warps. This flexibility means you're not locked into a narrow selection of cartridges. Moving magnets, high-output moving coils, and low-output moving coils can all work effectively with proper setup. Tracking force and anti-skating adjustments are straightforward, and the Cardas internal wiring preserves signal integrity from the headshell pins through to the RCA junction box.\u003c\/p\u003e\n\n\u003ch5\u003eMounting Configurations\u003c\/h5\u003e\n\u003cp\u003eThe Origine Tonearm is available in two mounting configurations, each engineered for a specific Oracle turntable platform. The Paris Mount is designed for the Oracle Paris turntable, with geometry matched to the Paris plinth and platter layout. The Delphi Mount is configured for the Delphi series, accounting for the different mounting position and armboard dimensions of that platform. Selecting the correct mount is essential for proper tonearm geometry, as the pivot-to-spindle distance, overhang, and offset angle all depend on the mounting configuration. If you're unsure which mount your turntable requires, reach out to us before ordering.\u003c\/p\u003e\n\n\u003ch5\u003eUpgrade Path: From Origine to Paris to Reference\u003c\/h5\u003e\n\u003cp\u003eThe Origine Tonearm sits at the entry point of Oracle's tonearm lineup, but it's built with the same attention to engineering as their higher-end models. When you're ready to move up, the \u003ca href=\"\/products\/oracle-audio-paris-tonearm\"\u003eOracle Paris Tonearm\u003c\/a\u003e offers gimbal bearings, a conical carbon fiber arm tube, and Oracle's Micro Vibration Stabiliser silicone damping system. Beyond that, the \u003ca href=\"\/products\/oracle-audio-reference-tonearm\"\u003eOracle Reference Tonearm\u003c\/a\u003e represents the top of Oracle's tonearm engineering. Each step up brings refinements in bearing precision, damping, and materials, but the Origine holds its own as a serious performer that punches above its price point.\u003c\/p\u003e\n\n\u003ch5\u003eExplore the Oracle Audio Tonearm and Turntable Range\u003c\/h5\u003e\n\u003cp\u003eThe Origine Tonearm pairs naturally with Oracle's turntable platforms. Here are the related products in the Oracle lineup.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-origine-mk2-turntable\"\u003eOracle Audio Origine Mk2 Turntable\u003c\/a\u003e\u003c\/strong\u003e - Oracle's entry-level turntable, ships with the Origine tonearm included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-paris-tonearm\"\u003eOracle Audio Paris Tonearm\u003c\/a\u003e\u003c\/strong\u003e - Gimbal-bearing upgrade with conical carbon fiber tube and silicone damping\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-reference-tonearm\"\u003eOracle Audio Reference Tonearm\u003c\/a\u003e\u003c\/strong\u003e - Oracle's flagship tonearm with the highest level of bearing precision and damping\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-delphi-mk-vii-classic-turntable\"\u003eOracle Audio Delphi Mk VII Classic\u003c\/a\u003e\u003c\/strong\u003e - The flagship Delphi platform, compatible with Delphi Mount configuration\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch5\u003eThe Listening Room Difference\u003c\/h5\u003e\n\u003cp\u003eWe're a third-generation family business with a brick-and-mortar showroom in Chestertown, Maryland, and a reputation built on trust, not hype. Whether you're visiting in person or ordering online, we bring decades of experience, personalized service, and honest guidance to every interaction. We don't just ship boxes. We help build systems, answer your questions like real humans, and make sure every detail of your setup is right, from the cables to the final connection. Our passion is helping you get the most out of your gear, with support that lasts well beyond the sale.\u003c\/p\u003e\n\n\u003ch5\u003eOracle Origine Tonearm Specifications\u003c\/h5\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTonearm Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eUnipivot\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArm Tube Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eCarbon fiber\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEffective Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e240mm (9.45\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePivot to Spindle Distance\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e223mm (8.78\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEffective Mass\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAdjustable via movable \"olive\" counterweight\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eInternal Wiring\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eCardas Audio\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eRCA junction box (included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMounting Configurations\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eParis Mount or Delphi Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCompatible Turntables\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eOracle Paris, Oracle Delphi series\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCountry of Origin\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHandcrafted in Sherbrooke, Quebec, Canada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Oracle Audio","offers":[{"title":"Paris Mount","offer_id":42547109625952,"sku":"ORACLEORIGPARIS","price":1580.0,"currency_code":"USD","in_stock":true},{"title":"Delphi Mount","offer_id":42561634435168,"sku":"ORACLEORIGDELPHI","price":1815.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0555\/5073\/8528\/files\/oracle-audio-origine-tonearm-white-bg.jpg?v=1770471710"},{"product_id":"oracle-audio-reference-tonearm","title":"Oracle Audio Reference Tonearm","description":"\u003cp\u003eThe Oracle Audio Reference Tonearm is Oracle's flagship arm, engineered from the ground up with a high modulus carbon fiber armtube, a precision four-bearing design, and Cardas HSL CLEAR 34\/4 Reference internal wiring running from headshell to output. Designed as the ultimate tonearm for Oracle's Delphi turntable platform, the Reference delivers the tracking precision and signal purity that high-end cartridges require to perform at their full potential.\u003c\/p\u003e\n\n\u003cp\u003eAt $6,000, the Reference competes with arms from SME, Graham, and Tri-Planar, but it was purpose-built for the Delphi's suspension geometry rather than adapted from a universal design. That distinction matters. The bearing tolerances, effective mass, and damping behavior are all optimized for the Delphi's floating sub-chassis, which means you get mechanical synergy that a bolt-on third-party arm cannot replicate. If you're running a Delphi with a cartridge north of $2,000, this is where the arm stops being the bottleneck. We recommend it to customers who have already heard what the Paris Tonearm can do and want to know what they're still leaving on the table.\u003c\/p\u003e\n\n\u003ch5\u003eKey Features of the Oracle Audio Reference Tonearm\u003c\/h5\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh Modulus Carbon Fiber Armtube:\u003c\/strong\u003e The armtube is constructed from high modulus carbon fiber, providing an optimal combination of rigidity and controlled resonance behavior that keeps the stylus tracking accurately across the entire record surface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecision Four-Bearing Design:\u003c\/strong\u003e A very high precision four-bearing assembly delivers exceptional tracking stability with minimal friction, ensuring consistent performance regardless of groove modulation levels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardas HSL CLEAR 34\/4 Reference Internal Wiring:\u003c\/strong\u003e Premium Cardas reference-grade wire runs the full length of the arm, from the headshell pins to the Cardas RCA connector junction box, maintaining signal integrity without compromise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecision VTA Calibration System:\u003c\/strong\u003e A dedicated vertical tracking angle adjustment system allows exact alignment of the stylus rake angle to match your specific cartridge and record thickness.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable Silicone Damping:\u003c\/strong\u003e A tunable silicone damping system lets you match the tonearm's mechanical behavior to your cartridge's compliance characteristics, controlling resonance without over-damping the signal.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated End-of-Record Auto Lift:\u003c\/strong\u003e A built-in mechanism automatically lifts the tonearm at the end of a record, protecting both your stylus and your vinyl from unnecessary wear.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20-Gram Effective Mass:\u003c\/strong\u003e The arm's effective mass of 20 grams makes it well-suited for low-compliance moving coil cartridges, which represent the majority of high-end designs available today.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch5\u003eCarbon Fiber Construction and Resonance Control\u003c\/h5\u003e\n\u003cp\u003eThe choice of high modulus carbon fiber for the armtube is deliberate and purposeful. Carbon fiber offers a higher stiffness-to-weight ratio than aluminum or other metals commonly used in tonearm construction, meaning the tube resists flexing under the dynamic forces of record playback without adding unnecessary mass. Equally important is how carbon fiber handles vibration. Rather than ringing at specific frequencies the way metal tubes can, carbon fiber dissipates vibrational energy more broadly across the frequency spectrum, reducing the chance of audible coloration being introduced into the signal. Oracle selected this material specifically because it allows the cartridge to do its job without the arm adding its own character to the sound.\u003c\/p\u003e\n\n\u003ch5\u003ePrecision Bearing Assembly\u003c\/h5\u003e\n\u003cp\u003eThe Reference Tonearm uses a very high precision four-bearing design that addresses both horizontal and vertical movement with minimal friction. Low bearing friction is critical in tonearm performance because it directly affects the arm's ability to follow the groove modulations accurately, especially at low frequencies where large stylus excursions require the arm to move freely. The four-bearing arrangement distributes the mechanical load evenly, reducing wear over time and maintaining consistent tracking performance throughout the life of the arm. This is not a unipivot or magnetic bearing design. It is a fixed-bearing approach that prioritizes mechanical stability and predictable behavior under all playing conditions.\u003c\/p\u003e\n\n\u003ch5\u003eCardas Reference-Grade Signal Path\u003c\/h5\u003e\n\u003cp\u003eOracle selected Cardas HSL CLEAR 34\/4 Reference wire for the internal wiring of the Reference Tonearm, and it runs uninterrupted from the headshell connector pins to the Cardas RCA junction box at the output. The HSL CLEAR line uses pure Cardas copper in a 34 AWG configuration wrapped in nylon microfiber rather than an extruded jacket, minimizing dielectric absorption and preserving the micro-level detail that high-end cartridges are capable of retrieving. By using a single continuous run of reference-grade wire with no solder joints or connector transitions between headshell and output, Oracle eliminates potential points of signal degradation along the way. The Cardas RCA junction box provides a clean, secure connection point for your preferred interconnect cables.\u003c\/p\u003e\n\n\u003ch5\u003eSetup Precision and Damping Control\u003c\/h5\u003e\n\u003cp\u003eThe Reference Tonearm includes a precision VTA calibration system that allows fine adjustment of the vertical tracking angle. Correct VTA alignment ensures the stylus sits at the proper rake angle in the groove, which directly affects frequency response, distortion levels, and the overall tonal balance of the playback. The adjustable silicone damping system provides an additional layer of tuning control. By varying the damping level, you can optimize the tonearm's behavior for your specific cartridge's compliance characteristics. Higher-compliance cartridges may benefit from lighter damping to preserve dynamics, while lower-compliance designs might perform better with additional damping to control the arm\/cartridge resonance frequency. The integrated end-of-record auto lift mechanism provides peace of mind by automatically raising the arm when the record reaches its innermost groove.\u003c\/p\u003e\n\n\u003ch5\u003eDesigned for the Delphi, Compatible with More\u003c\/h5\u003e\n\u003cp\u003eThe Reference Tonearm was designed first and foremost for Oracle's Delphi turntable platform. The Delphi Mk VII comes equipped with a pre-cut tonearm board that accommodates 9 and 10-inch tonearms, and the Reference mounts directly to the Delphi's armboard for a seamless mechanical and visual integration. That said, the Reference Tonearm is not exclusively limited to the Delphi. It can be mounted on other turntables that accept standard 9 or 10-inch tonearm mounting geometry, though the Delphi remains the platform where Oracle has optimized every aspect of the arm's performance.\u003c\/p\u003e\n\n\u003ch5\u003eExplore the Full Oracle Audio Tonearm Range\u003c\/h5\u003e\n\u003cp\u003eOracle offers tonearm options at multiple price points, each built to complement their turntable platforms.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-paris-tonearm\"\u003eOracle Audio Paris Tonearm\u003c\/a\u003e\u003c\/strong\u003e - Oracle's mid-range tonearm option featuring carbon fiber construction and their Micro Vibration Stabiliser silicone damping system.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-origine-tonearm\"\u003eOracle Audio Origine Tonearm\u003c\/a\u003e\u003c\/strong\u003e - A unipivot design with adjustable effective mass, built for Oracle's Origine turntable platform.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-delphi-mk-vii-classic-turntable\"\u003eOracle Audio Delphi Mk VII Classic Turntable\u003c\/a\u003e\u003c\/strong\u003e - The turntable platform the Reference Tonearm was designed for.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-delphi-mkvii-reference-turntable\"\u003eOracle Audio Delphi Mk VII Reference Turntable\u003c\/a\u003e\u003c\/strong\u003e - The Delphi with upgraded power supply, an ideal match for the Reference Tonearm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/oracle-audio-delphi-mkvii-signature-turntable\"\u003eOracle Audio Delphi Mk VII Signature Turntable\u003c\/a\u003e\u003c\/strong\u003e - Oracle's ultimate turntable, built for the listener who accepts nothing less.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch5\u003eThe Listening Room Difference\u003c\/h5\u003e\n\u003cp\u003eWe're a third-generation family business with a brick-and-mortar showroom in Chestertown, Maryland, and a reputation built on trust, not hype. Whether you're visiting in person or ordering online, we bring decades of experience, personalized service, and honest guidance to every interaction. We don't just ship boxes. We help build systems, answer your questions like real humans, and make sure every detail of your setup is right, from the cables to the final connection. Our passion is helping you get the most out of your gear, with support that lasts well beyond the sale.\u003c\/p\u003e\n\n\u003ch5\u003eOracle Audio Reference Tonearm Specifications\u003c\/h5\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArmtube Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHigh modulus carbon fiber\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBearing Design\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eVery high precision 4-bearing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEffective Mass\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20 grams\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eInternal Wiring\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eCardas HSL CLEAR 34\/4 Reference\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOutput Connection\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eCardas RCA connector \/ DIN junction box\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eVTA Adjustment\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePrecision calibration system\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDamping\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAdjustable silicone system\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAuto Lift\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIntegrated end-of-record mechanism\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFinish\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eCarbon fiber and brushed aluminum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCompatible Turntables\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eOracle Delphi (primary), other turntables accepting 9\/10-inch arms\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMade In\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eQuebec, Canada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e","brand":"Oracle Audio","offers":[{"title":"Default Title","offer_id":42547110019168,"sku":"ORACLEREF1","price":8900.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0555\/5073\/8528\/files\/oracle-reference-tonearm.png?v=1770472957"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0555\/5073\/8528\/collections\/oracle-audio-tonearms-hero.png?v=1778094776","url":"https:\/\/listenroom.com\/collections\/oracle-audio-tonearms.oembed","provider":"The Listening Room","version":"1.0","type":"link"}